GE oven flashing F2, F9 or another F-code
Houston Appliance Care takes calls on GE wall ovens, ranges, dishwashers and refrigerators, and this page starts with oven fault codes because a couple of them mean stop cooking now. GE's own guidance for every range and wall oven code is to have a trained technician look at it. What changes from code to code is how urgent it is and which part your tech tests first.
F2 or F20 says the oven went past its temperature limit. Leave it off. The tech checks the oven sensor, the relay on the control and the control board, since a fault in that chain can let the heat keep climbing.
F3 or F4 points at the oven temperature sensor, one of the cheaper oven parts on national figures. F9 or FC is the door lock circuit, and a self-clean cycle is one time it can show up. If the door stays latched after the oven has cooled, leave it shut so the tech can test the lock motor and its switches before anything gets forced.
FD involves the meat probe or the jack it plugs into. F0, F1, F6 and F7 point to the keypanel, and F5, F8 and FF to the electronic control. Bake elements and igniters that die without any code are covered on the range and wall oven repair page, and the appliance error code library puts GE's codes next to other brands'.
GE oven too hot or locked shut right now
Do these before anything else, then pick up the phone.
- Turn the oven off and switch off its breaker. GE notes that a minute or two without power sometimes clears a code, but an F2 that comes back means the oven stays off.
- Don't pry at a locked door. The latch is one of the parts that gets tested, and forcing it can turn a switch repair into a latch repair.
- Keep kids and pets away from the oven front while it cools down.
- Write the code down exactly as the display shows it, letters and numbers, and call us with it.
GE dishwasher stopped on a C-code
GE says most of its dishwasher fault codes need a technician, and not every code shows on every model. Two displays aren't faults: a number followed by H (1H, 2H) is Delay Start counting down, and PF means the power blinked mid-cycle. The right-hand column below is what each code usually points to. Pumps, valves and latches that fail without a code are on the GE and other dishwasher repair page.
| Code | What it means | What the tech checks |
|---|---|---|
C1 / C2 | Pump-out ran too long: over 2 minutes in one drain, or over 7 minutes in total. | The drain path: hose, air gap, disposal inlet, filter, then the drain pump. |
C3 | Won't drain. | Drain hose, the air gap at the sink and the disposal connection, then the drain pump itself. |
C4 | Filled twice after a power failure. | The float under its cup in the front left corner of the tub, and debris in the sump holding it up. |
C6 | Water reaching the tub is cooler than GE wants. | Inlet water temperature against GE’s 120°F minimum. If that’s fine, the heater and its thermostat. |
C7 | Temperature sensor circuit not working. | The sensor and its wiring back to the control. |
C8 | Detergent cup blocked from opening. | Often a tall pan in the way of the cup door. If the cup is clear, the dispenser. |
H2O | Low water. | A kinked inlet hose, the supply valve under the sink and the water inlet valve. |
PrS | Pressure sensor fault. | The pressure sensor that reads the water level. |
FTD / F56 | Failure to drain. | The same drain path as C3. |
GE refrigerator running warm or slow on ice
Food safety guidance from the FDA and USDA is 40°F or below on the fresh-food side and 0°F in the freezer. If you have an appliance thermometer, give us both readings on the call.
GE fridge runs constantly out in a Houston garage
GE ice bin slow to refill after a party
GE ice maker makes no ice with the freezer at 0°F
GE fridge warm, freezer still cold
GE fridge and freezer both warm
What GE repairs cost, part by part
These are typical national ranges, parts and labor together, lined up with the codes and symptoms above. Your own number comes from the tech once the fault is found, written down for you to approve. You only pay for work you agreed to.
| Repair | Typical range | Notes |
|---|---|---|
| Service call with diagnosis | $70 to $130 | Usually covers the diagnosis and the first hour of labor |
| Oven temperature sensor (F3, F4) | $100 to $250 | |
| Oven control board (F5, F8, FF) | $150 to $600 | Part alone $60 to $250 |
| Dishwasher drain pump (C1, C2, C3) | $100 to $400 | Part alone $20 to $100 |
| Dishwasher float switch (C4) | $90 to $190 | |
| Dishwasher heating element (C6 with hot water at the sink) | $200 to $350 | |
| Dishwasher water inlet valve (H2O) | $80 to $170 | |
| Refrigerator evaporator fan motor | $250 to $400 | |
| Ice maker repair | $100 to $225 | |
| Refrigerator compressor | $700 to $1,250 | Compressor part alone $200 to $400 |
Work on a gas range’s connector or supply line falls under Texas plumbing law, covered on how Houston Appliance Care works. Every appliance type is priced in the appliance repair cost guide, and a GE past ten years is weighed in the repair or replace guide.
Reading your GE serial number for its age
A GE serial number runs two letters, six digits, then one more letter, and the first two letters are a date stamp. Read them to us when you call. They tell the tech how old the appliance is, and they count for the warranty too, because GE uses the build date to set coverage when there's no proof of purchase.
- First letter: the month
- A January, D February, F March, G April, H May, L June, M July, R August, S September, T October, V November, Z December.
- Second letter: the year
- H 2017, L 2018, M 2019, R 2020, S 2021, T 2022, V 2023, Z 2024, A 2025, D 2026.
- The 12-year repeat
- Year letters come around again about every 12 years. GE’s own example, AD, means January 2002 or January 2014, and on the current cycle January 2026 as well. The look of the appliance usually tells you which.
- Reading a real pair
- RS is August 2021, or August 2009. ZA is December 2025, or December 2013.
GE warranty: the first year and the sealed system
GE Appliances backs its products with a 1-year limited warranty, and GE says some appliances carry extra coverage on specific parts past year one. The refrigerator is the big one. GE's current fridge manual gives GE Profile and Café models five years of parts and labor on the sealed system: the compressor, condenser, evaporator and connecting tubing. Standard GE refrigerators get the one-year term.
So a two-year-old GE Profile French door with a dead compressor and a three-year-old GE dishwasher with a failed drain pump are different calls. The fridge may still sit inside sealed-system coverage. The dishwasher is past year one, and unless the owner's manual lists the drain pump, that repair is yours. Read us the badge on the door along with the serial number, because Profile or plain GE changes the answer.
No receipt? GE goes by the manufacturing date then, and an appliance can sit in a warehouse or a showroom for months before anyone buys it. A delivery email or a card statement with the purchase date on it does the same job as a receipt.
Café, Monogram, Profile and Hotpoint repair
GE Appliances calls itself a house of brands and sells under six names. Haier bought GE Appliances in a deal that closed June 6, 2016, and the company is still based in Louisville, Kentucky. A Hotpoint top-freezer or a Café range comes from the same company as a plain GE. Give us the badge on the door and the model number when you call, especially for a Monogram built-in, so the tech knows exactly which unit and which parts list the job involves.
- GE
- GE Profile
- Café
- Monogram
- Hotpoint
- Haier
GE repair questions, answered
Can I keep using my GE oven after it showed F2?
No. F2 and F20 mean the oven went past its temperature limit, so keep it off at the breaker until the sensor and the control have been tested. National averages put a sensor replacement at $100 to $250 nationally and a control board at $150 to $600.
Does a GE dishwasher showing C6 have a bad heater?
Often it's the water supply. C6 means the water arriving at the tub is under GE's 120°F mark, so the tech checks the inlet temperature first. If the kitchen tap runs hot and C6 keeps coming back, the heating element or its thermostat gets tested. An element runs $200 to $350 on national figures.
My GE fridge is two years old. Is the compressor still covered?
On a GE Profile or Café, it may be. GE's current refrigerator warranty gives those two lines five years of parts and labor on the sealed system, compressor included, while a standard GE model gets one year. Read us the serial number and the purchase date on the call. The tech then confirms whether the failure is in the sealed system or in a cheaper part such as a fan or a start relay.
Can you send someone for a Monogram or Café appliance?
Tell us the badge and the model number when you call, and we'll book the visit around that model. Both are GE Appliances lines. Monogram built-ins especially need the exact model, because the parts differ from a standard GE.
What does a GE repair visit cost?
The national range for a service call is $70 to $130, which usually covers the diagnosis and the first hour of labor. The repair price comes after the tech finds the fault, written down, and nothing gets done until you've said yes to it.
