Samsung Washer Won't Fill, Drain or Spin? The Codes Behind It
On a Samsung washer, 4C means it isn't filling, 5C or nd means it isn't draining, UE flags an unbalanced load and dE points at the door. Samsung shows one error under several spellings, and a leading 1 on some displays (1 4C, 1 5C) is the same code. Blinking lights alone count as an error only when the washer also stops working normally, Samsung says.
| Code | What it means | What the tech checks |
|---|---|---|
4C, 4E, nF, 1 4C | Not filling: water isn't getting in correctly | Usually the supply: a closed valve, a kinked hose or grit in the inlet screens. The tech checks the supply first, then the inlet valve. |
4C2, 4E2, CE, 14C2, nF1 | Hot/cold error: the cold supply is running extremely hot | Usually the hot and cold hoses are swapped at the back, which Samsung says doesn't need a repair. |
nd, 5C, 5E, SC, SE, 1 5C | No drain, or draining too slowly | Points to the drain filter, a kinked drain hose or the drain pump. How far the hose sits in the standpipe gets checked before the pump. |
UE, Ub, U6, 1 Ub, 1U6 | Unbalanced load; the cycle won't finish | A tangled load is the usual cause, and Samsung's first step is spreading it out and pressing Start again. If it repeats on normal loads, the tech checks the leveling and, on a new front-loader, the shipping bolts. |
Ur | Unbalanced load retry, shown while the washer rebalances | Nothing is broken. The washer is retrying the spin on its own. |
dE, dE1, dE2, dC1, dL, dS, FL, LO | Door not detected as closed and locked | Often a sock caught at the seal. If the door shuts cleanly and the code stays, the latch and door lock get tested. |
dC | Door error on some models, unbalanced load on others | The model decides which, so read us the model number off the label along with the code. |
LE, LC, 1E, 1C, LC1 | Leak detected, or a water level error | Points to a slow leak under or behind the washer, a kinked hose, or heavy suds from too much or non-HE detergent. |
OE, 0E, OC, 0C, 1 OC | Overflow: too much water in the tub | A fill valve that won't shut off is one possible cause, and it's what the tech tests when the code keeps returning. |
9C1, 9C2, PF, 2E, 9E1, 9E2, UC | Voltage or power supply irregularity | Samsung asks for an outlet on its own circuit, without an extension cord. After a storm outage, one restart is reasonable; if it repeats, mention it on the call. |
Rarer Samsung Washer Codes, and the Ones That Aren't Faults
For any code without its own steps, Samsung's instruction is a 2 to 3 minute power reset, then service if the code returns. The first six rows below aren't faults at all.
| Code | What it means | What the tech checks |
|---|---|---|
SUd, Sd, 5Ud, SUdS | Too many suds | Not a fault. Less detergent, HE formula. |
Cb, C6 | Calibration mode | Not a fault. It only calibrates correctly with an empty drum. |
dn | Downloading a software update | Not a fault. Samsung says the update takes about 15 minutes, with the controls locked meanwhile. |
CL | Child Lock drained the tub after the door was opened | Not a fault. Switching Child Lock off clears it. |
SDC, 5DC | Detergent drawer not fully closed | Not a fault once the drawer is fully shut. |
ddC, dC3 | Add Door (the small door-in-door) not latched | Usually clothing in the latch, or the small door not pushed shut. |
E2, bE2, 6E2 | A control panel button reads as stuck | A jammed or damaged button; the control panel gets checked if it stays. |
3E, 3C, E3, 1 3C | Motor error (a voltage error on some models) | The tech tests the motor. Your model number decides which meaning applies. |
HE, HC, HE1, Hr | Heater error | The washer's water heater gets tested. |
tE, tE1, tC | Temperature sensor error | Points to the temperature sensor. |
PE, PC; PE1, PC1 | Clutch position error; clutch hall signal error (top-loaders) | Points to the clutch assembly on a top-loader. |
AE, AC and variants | Communication error between boards | The boards and the wiring that links the boards get checked. |
8E, BE, 8C, BC | MEMS or vibration sensor error | Points to the vibration sensor. |
bE, 6E | Motor speed sensor error | Points to the motor speed sensor. |
LG Front-Loader Showing a Code?
On an LG, LE means the motor is locked or strained, not a leak, which trips up anyone used to Samsung codes.
| Code | What it means | What the tech checks |
|---|---|---|
IE | Inlet error: the tub didn't fill in time | The faucet, a bent hose or a gritty inlet screen; then the inlet valve |
OE | Drain failure | The drain pump filter, a kinked drain hose or heavy suds; then the pump |
UE | Load out of balance | A lopsided load or a washer that sits off level |
dE, dE1, dE2 | Door error: not shut properly or not locking | Clothing caught in the gasket first, then the door switch and lock |
LE | Tub won't spin because the motor is strained | An overload, or a coin or other object in the drum. LG's reset is 5 minutes unplugged; past that, the motor gets tested. |
CE | Motor current error | If it repeats after a restart, the motor and control get checked |
tE | Heating or temperature control error | The heater circuit and the thermistor get tested |
PE | Water level sensor fault | The level sensor, if it keeps showing |
FE | Overfilled | Water coming in when it shouldn't; the inlet valve gets checked |
dHE | Temporary dry-function fault on washer-dryer combos | A reset, then service if it returns |
CL, tCL, SUD, PF | Child lock on; Tub Clean due; too many suds; power cut mid-cycle | Not faults. Nothing needs repair once the setting, the cleaning cycle, the detergent or the power is sorted out. |
Whirlpool or Maytag Washer Flashing a Code?
Whirlpool Corporation owns Maytag, and Maytag publishes the same top-load codes. Front-loaders use F-and-E pairs; top-load HE machines show short words. Brand detail is on the Whirlpool appliance repair and Maytag appliance repair pages.
| Code | What it means | What the tech checks |
|---|---|---|
F8 E1, Lo FL, LF | Taking too long to fill | Both faucets have to be on and hooked up; then the hose screens and the inlet valve |
F9 E1, drn | Slow or failed drain | Often the install, such as a kinked drain hose or one pushed too far into the standpipe. Then the pump filter on front-loaders. |
F5 E2 | Front-load door not locking | Laundry or debris at the latch first, then the door lock itself |
rL | Items found in the drum during Clean Washer | Not a fault. Empty the drum and restart the cleaning cycle. |
LdL, LdU, lid | Lid won't lock; lid stuck locked; lid left open (top-load) | Something sitting on the lid or a lid not fully shut; then the lid lock |
Ofb, OL | Balancing in progress; load too large | Not faults. Let it correct, or take a few items out. |
Sud | Too many suds | Less HE detergent |
HC | Hot and cold hoses reversed | The hoses are swapped at the washer |
PF | Power failure | Start the cycle again |
Samsung or LG Fridge Showing a Code?
Most of these point to a fan, a sensor or the defrost system, and both makers send them to service. LG notes that frost on the fan is a common reason for its FF code. The refrigerator and freezer repair page has the parts behind these codes.
| Code | What it means | What the tech checks |
|---|---|---|
Samsung 5E | Fresh-food defrost sensor | Leave the code on the display so the tech can read it before testing the sensor |
Samsung 8E, 14E | Ice maker sensor | Leave the code showing for the tech |
Samsung 21E | Freezer fan | Often ice on the fan, a door left ajar or a gap in the gasket |
Samsung 22E, 22C | Fresh-food fan | Usually ice on the fan. If the code keeps coming back, the defrost parts behind the frost get tested. |
Samsung 33E, 39E, 39C, 40E, 40C | Ice pipe heater; ice maker function; ice room fan | Service: the tech tests the heater, ice maker or fan the code names |
Samsung 83E, 85E, 86E | Compressor current, under-voltage or over-voltage | Often a surge or brownout. Samsung says to cut power for 60 seconds; a code that comes back needs service. |
Samsung 84C | Locked compressor | Sealed-system work, so the purchase date matters for the warranty. |
Samsung OF OF, O FF | Cooling Off demo mode; nothing is broken | Not a repair. Demo mode switches off from the control panel, and we can walk you through it on the call. |
LG IF, FF, CF, rF | Ice maker fan, freezer fan, condenser fan, fridge fan | LG routes these to service. Frost on the fan is a common cause, so the defrost system gets tested along with the fan. |
LG dH (FdH, dHF) | Defrost cycle ran too long without the sensor warming up | The evaporator may be iced over; the defrost system gets tested |
LG rS, FS, dS | Fridge, freezer or defrost sensor fault | The named sensor gets tested |
LG CO | Main board and display not communicating | The link between the main board and the display gets traced |
Samsung Dryer Codes for Heat, Vent and Door
On these codes the tech starts with airflow, since a blocked vent also blows thermal fuses.
| Code | What it means | What the tech checks |
|---|---|---|
tE, tC, tS, tO | Temperature reading out of range | Airflow first, from the lint screen to the vent outlet outside, then the temperature sensor |
hE, HC | Heating fault | The same airflow check, then the heating parts |
C8, C80, C9, C90, Clg, Cg | Result of the vent blockage test | A clogged lint filter or exhaust duct |
dC, dE, dF, do, d0 | Door switch | A door not shut firmly, or a worn latch or switch |
9C1, 9E, 2E | Supply voltage | Samsung wants a dedicated circuit and no extension cord |
FC, FE | Power frequency | Restart once; a repeat goes to service |
Samsung or Frigidaire Dishwasher Not Draining or Filling?
Samsung and Frigidaire both publish dishwasher codes. The dishwasher repair page covers the drain pumps, filters and heaters behind them.
| Code | What it means | What the tech checks |
|---|---|---|
Samsung 4C, 4E | No water supply | The water valve under the sink and the inlet hose, then the inlet valve |
Samsung 5C, 5E, SC, SE | Drain problem | A clogged filter or drain hose, then the drain pump |
Samsung LC, LE | Moisture detected in the base | A leak underneath; the tech traces where the water comes from |
Samsung OC, 0C, oE | Too much water | Service if it repeats |
Samsung HE, HC | Heating error | The heater and the temperature sensor get checked |
Frigidaire i20 | Didn't drain completely | The disposer knockout plug on a new install or a pinched drain hose, then the filter and sump |
GE or Frigidaire Oven Showing an F Code?
An F code on a range or wall oven points to a part, and the tech tests that part on the visit. Brand detail is on the GE appliance repair and Frigidaire appliance repair pages.
| Code | What it means | What the tech checks |
|---|---|---|
GE F2 | Oven went past its temperature limit | Stop using the oven until the sensor and control get tested |
GE F3, F4 | Oven sensor | The tech tests the sensor |
GE F9 | Door lock circuit | The door lock and its circuit |
GE FD | Meat probe or its socket | Say whether the probe was in use when the code appeared |
Frigidaire F10 | Thermal runaway: running hotter than normal | Stop using the oven; the sensor and the control get tested |
Repairing the Part Behind the Code
A code narrows the search, and the tech still tests the part behind it. These pages cover the repairs the codes above lead to most often.
- Washer repair in HoustonDrain pumps, door locks, inlet valves and bearings behind the fill, drain and spin codes.
- Samsung appliance repairCommon Samsung washer, dryer and fridge failures, and the warranty terms worth mentioning on the call.
- LG appliance repairWhat LG covers on drum motors and compressors, and the failures behind its codes.
- Dryer repair for no heatThermal fuses, heating elements and the vent problems behind temperature codes.
- Oven and range repairSensors, igniters and control boards behind F codes on GE and Frigidaire ranges.
Error Code Questions
How do I reset a Samsung washer error code?
Turn it off, cut the power at the plug or breaker, wait, then restore it and start a cycle. Samsung says 1 minute for a fill code and 2 to 3 minutes for codes without specific steps. If the same code comes back, the part behind it needs testing.
Is it safe to keep using a washer that shows a code?
It depends on the code. Suds, calibration, Ur and download messages are normal operation. A leak code (LE or LC on a Samsung) is worth a call before the next load, since water under a washer can damage the floor. Heater, motor and sensor codes that return after a reset mean stop and book a repair.
Why did my washer show PF after the power came back?
On LG and Whirlpool washers, PF means power was lost during the cycle; Samsung lists PF with its voltage errors. After a Houston storm outage or a tripped breaker, restart the cycle once. If PF keeps showing with no outage, mention it on the call and keep the washer off extension cords.
My code isn't on this page. What now?
Write it down exactly, including any leading 1 and the letter case, and read it to us with the model number when you call. Codes differ between models even within one brand, and the tech checks yours against your model before testing parts.
Does the same code mean the same thing on every brand?
No, and a few overlap in confusing ways. LE is a leak or water level code on a Samsung washer but a strained-motor code on an LG. dC is a door code on some Samsung models and an unbalanced load on others, so the brand and model number decide it.
