Electric & gas dryers

Houston Dryer Repair for Cold, Slow Dryers

Gas and electric dryer repair when the drum blows cold, squeals or needs two cycles per load. Every visit starts at the vent.

Dryer with its door open and a lint screen thick with lint

Dryer tumbling but blowing cold air

A Whirlpool, Maytag, Samsung, LG or GE dryer that turns but won't heat usually comes down to one of these: half of a tripped breaker, a closed gas valve, a burned-out heating element, a blown thermal fuse, a failed thermostat, a cracked igniter or tired gas valve coils, or a vent packed with lint.

Electric dryers run on a 240-volt, 30-amp circuit fused on both sides of the line, Whirlpool explains, so there are two breakers. One side can keep the motor turning while the other side, the one feeding the heating element, has tripped. That's why a drum that spins with no heat at all gets its power checked on both legs before anyone opens the cabinet.

On a gas dryer, the shutoff valve on the pipe behind the machine is the first stop. Whirlpool's rule: handle parallel to the pipe is open, crosswise is closed. A closed valve lets the drum spin normally with no heat, and a valve gets bumped easily when a dryer is pulled out or moved into a new house. Tell us on the call if the dryer was moved lately.

With power and gas confirmed, the fault is inside. Reaching the heating element or the thermal fuse means taking the dryer apart, and the tech tests the fuse, the high-limit and cycling thermostats, and then the element or the ignition parts, depending on the fuel.

Gas and electric dryer heating repair

The drum, belt and motor work the same on both. The heat source is where they split.

Electric dryers

  • A coiled heating element warms the air. When the coil breaks, the dryer runs cold, and replacing it runs $150 to $350 nationally.
  • The element itself runs about $15 to $35 as a generic part, or up to $200 from the maker.
  • A half-tripped breaker or a loose wire at the cord terminal block can look exactly like a dead element.
  • A high-limit thermostat that keeps tripping usually means the exhaust is being held back somewhere.

Gas dryers

  • A hot-surface igniter glows to light the burner. A cracked one stays dark, and the drum turns with no flame.
  • If the igniter glows but the flame never catches, weak gas valve coils are a common cause.
  • A faulty flame sensor can leave the igniter glowing while no gas flows.
  • Work on the gas connection itself falls under Texas plumbing law, and how a repair visit works explains who handles it.
Dryer heating element coil on a workbench beside a multimeter

Loads taking two cycles, squealing and other dryer faults

Once heat is ruled in or out, most dryer problems show up as one of these.

Dryer heats, but a load takes two cycles

The CPSC names long drying times as a warning sign of a blocked lint screen or exhaust duct. Whirlpool adds two causes that aren't faults at all: an overstuffed drum, and clothes that went in dripping because the washer didn't spin them out. If loads come out of the washer soaking, the washer repair page is the place to start. On the visit: The tech checks the airflow at the outside vent flap with the dryer running, then the duct behind the machine.

Dryer quit heating right after the vent got clogged

That order of events fits a blown thermal fuse, a one-time safety part that cuts the heat when the exhaust runs too hot. A blocked vent is the usual reason it blows. The fuse is one of the cheaper lines on the price table, but a new one on the same clogged vent can blow again. On the visit: The tech tests the fuse for continuity, then checks the vent so the new fuse lasts.

Dryer squealing, thumping or scraping at the drum

Worn drum rollers, a glazed or stretched belt, or an idler pulley with a dry bearing. A steady thump on every turn often means a roller with a flat spot. On the visit: The tech takes the belt off and turns the drum by hand to find which roller or pulley drags.

Dryer motor hums but the drum won't turn

A snapped belt lets the motor spin with nothing to turn. A seized idler pulley or a motor bearing makes it hum and struggle, and a stalled motor heats up fast. Motor replacement runs $150 to $400. On the visit: The tech checks the belt and the idler first, since a seized pulley can make a healthy motor hum.

Dryer shuts off mid-cycle, or the top feels unusually hot

Overheating trips the cycling or high-limit thermostat, and the usual root cause is air that can't get out. The vent gets ruled out before anyone puts a control board on the table, which runs $250 to $500 nationally. On the visit: The tech measures the exhaust flow and tests both thermostats before looking at the board.

Dryer dead: no lights, no hum

The breaker and the door switch come first. On many models a blown thermal fuse also cuts power to the motor, so a dryer that won't start at all can still be a vent story. Samsung dryers report door faults as dC, dE or dF. On the visit: The tech checks power at the terminal block, the door switch and the thermal fuse, in that order.

Overheating dryer and gas odor problems

Stop and do these before anything else.

  • Scorched smell, or a cabinet too hot to keep a hand on: stop the dryer, unplug it and leave it off until the vent has been checked end to end.
  • Motor straining or humming without turning the drum: switch it off so the motor doesn't overheat.
  • Smell gas near a gas dryer: leave the house on foot without flipping switches or starting a car, and report the leak to your gas company from outside before anything else.
  • Once everyone is safe, call us and tell us what you saw or smelled.

Clogged or crushed dryer vent

Lint that gets past the screen ends up in the duct, and a dryer pushing against a clogged duct runs hot and slow. Failure to clean is the leading cause of dryer fires in residential buildings: 34% of an estimated 2,900 a year in U.S. Fire Administration figures for 2008 to 2010.

Plenty of newer dryers flag it themselves. Samsung shows C8, C9 or Clg after its vent blockage test and points to the lint screen and exhaust vent for its tE and hE heat codes too. Whirlpool shows AF or Check Vent and keeps running while the warning is up. LG's d90 and d95 mean the dryer has measured a 90% or 95% blockage, and LG says not to use it until the exhaust has been cleaned. The appliance error code library lists the rest.

On the visit the tech checks the connector behind the dryer for kinks and crushing, the run to the outside for lint, and the flap at the wall or the cap on the roof. A laundry room in the middle of the house that vents through the roof is a much longer job than a short run straight out a back wall, and a crushed foil or white vinyl connector gets swapped for a metal one. Vent cleaning and a new duct both have a line on the price table below.

Whirlpool's interval for cleaning the vent run is every one to two years, sooner once loads start taking longer.

Crushed foil dryer vent duct behind a dryer

What dryer repairs cost

National averages, parts and labor included, with the typical dryer repair around $200. The price for your dryer comes in writing after the diagnosis, and the tech doesn't swap a part until you say yes.

RepairTypical rangeNotes
Service call and diagnosis$70 to $130
Thermal fuse$75 to $150The fuse alone is $5 to $10 generic, up to $60 from the maker
Gas igniter$100 to $250
Belt$100 to $250
Drum rollers$100 to $300
Timer$120 to $300
Heating element$150 to $350Electric models
Motor$150 to $400
Idler pulley$200 to $350
Drum$200 to $500
Control board$250 to $500
Vent cleaning$80 to $185New duct: $100 to $300

A new dryer averages $800 to $1,200 nationally. For washer, fridge and kitchen repair prices, see the appliance repair cost guide.

Is an older dryer worth repairing?

Dryers are simple machines and they last. NAHB's life-expectancy figures put a dryer at about 13 years, a few more than the washer next to it. Most dryer parts also sit low on the price table, so a belt, fuse, roller kit or igniter on a 10-year-old dryer is usually money well spent.

The math turns when the big parts go. A $500 control board or drum on a 12-year-old dryer is close to half the $800 to $1,200 price of a new one, which is the 50% point Consumer Reports uses for repair or replace. Maytag's 10-year limited parts warranty covers the dryer's drive motor and drum (parts only after the first year), which can change the answer, so have the purchase date handy. The repair or replace guide walks through the same test for other appliances, and the Maytag dryer repair page has that brand's terms.

Dryer types and brands repaired

When you call, give us the brand, whether it runs on gas or electric, and roughly how long a normal load takes now. On a front-load Maytag dryer, open the door and look around the opening for the model label. Whirlpool Corporation owns the Maytag, Amana and KitchenAid brands, and the Whirlpool appliance repair page covers its codes and warranty. Dryer calls are taken in Houston and in parts of the cities next door, including Bellaire, Stafford, Missouri City and Sugar Land; the service areas page lists covered ZIPs. Don't see your ZIP? Call anyway and we'll check your address.

Dryer repair and vent questions

How do I know if my dryer vent is clogged?

Long drying times are the first sign the CPSC names. A cabinet that runs hot and a weak puff of air at the outside flap point the same way. Samsung, Whirlpool and LG dryers may also flag it with a vent code such as C8, AF or d90. The tech checks the duct and the flap on the visit.

Can I keep using my dryer if the vent is clogged?

Better not. A restricted vent drives exhaust temperatures up and trips safety parts, and the U.S. Fire Administration lists failure to clean as the leading factor in residential dryer fires. Leave it off and call. The tech clears the vent before replacing any fuse it blew.

Why does my gas dryer heat for a while and then go cold?

Weak gas valve coils are a common cause. They can open the valve while cool and fail once warm, so the burner lights, goes out and won't relight. A cycling thermostat or a vent restriction tripping the high-limit can look the same, so the tech tests the airflow and the coils together.

How much does a dryer thermal fuse cost to replace?

$75 to $150 installed, going by national averages, with the fuse itself $5 to $10 generic or up to $60 from the maker. The fuse is the easy half of the job. A blocked vent is what usually blows it, so the tech checks the vent before calling the repair done.

Dryer unplugged and a basket of damp towels

On the visit the tech checks the vent and the heat parts, then sets out the price in writing. You only pay for work you agreed to.

Call (713) 379-8612