Dishwashers

Dishwasher Repair in Houston for Drains and Leaks

Dishwasher repair for machines that hold gray water, leak at the door or stall mid-cycle. Say the brand and the code, and we'll set up the repair.

Open built-in dishwasher with the lower rack pulled out

Dishwasher not draining

Maytag says a little water left in the sump under the filter is normal from time to time, and it draws the line at about an inch. More than that left in the tub after a cycle points to a clog or a part that's quit, and the repair depends on where the water stopped: at a filter packed with seeds and label paper, in a crushed drain hose, at a blocked air gap, in the garbage disposal, or at a drain pump that no longer turns.

On the visit the tech listens to the drain part of the cycle before taking anything apart. A steady hum with no water moving usually means something hard is wedged against the pump impeller, and Whirlpool notes glass can end up in the pump area. Silence where the pump should be running points to the pump motor, its wiring or the control board. If gray water gurgles up in the sink, the block is downstream of the machine.

New plumbing under the sink is its own case. A new disposal comes with a knockout plug sealing the dishwasher inlet, and Frigidaire lists that plug first among its checks for the i20 "did not drain" code. Frigidaire also wants the drain hose to climb at least 32 inches. Where the dishwasher drains through the disposal, a jammed or slow disposal shows up as a dishwasher that won't empty. That side of the sink is covered on the garbage disposal repair page.

Hands rinsing a dishwasher filter under a kitchen faucet

Dishwasher model number and code

A minute of detail on the phone lets the tech show up with the likely part instead of a guess. Say whatever you know; none of it is required to call.

  • The brand, and the model number from the sticker along the side edge of the door
  • Any code or blinking-light pattern, exactly as the panel shows it (i20, 5C and LC are common ones)
  • Where the water is: standing in the tub, at the front of the door, or out from under the machine
  • Whether a disposal, faucet or sink went in shortly before the trouble started
  • Roughly how old the dishwasher is, and the purchase date if it might still be under warranty

Dishwasher leaks, wet dishes and stalled cycles

Draining is one way a dishwasher fails. These are the others, with the parts usually behind each one.

Puddle at the front corner of the door
A door gasket that's torn or flattened, suds from hand dish soap foaming over the seal, or a spray arm with a cracked hub throwing water at the door. A machine sitting out of level can also tip water toward the front. On the visit: The tech runs a short cycle and watches. Water at the door corner and water from under the kick plate lead to different parts.
Water spreading out from underneath
Usually a part behind the lower panel: the water inlet valve, the supply line fitting, the drain hose clamp or a pump seal. Samsung dishwashers show LC or LE when a sensor in the base picks up moisture. On the visit: The tech pulls the lower panel and follows the drip to its source. Until then, shutting the supply valve under the sink keeps a slow leak off the subfloor and cabinet base.
Cycle runs for hours and the load still comes out wet
Cool incoming water makes the machine pause to heat it, which Whirlpool says stretches the cycle. A failed heating element or high-limit thermostat shows the opposite: a normal run time and a cold, wet load. Many newer models dry by condensation with rinse aid, so damp plastics on those are expected. On the visit: The tech checks the water temperature reaching the machine, then tests the heating element and the high-limit thermostat.
Won't start, or stops partway with the lights on
A door latch or switch that doesn't register the door as closed, a child lock left on, or a control board fault. Samsung files 4C and 4E under water supply, which points back to the supply valve and hose under the sink. On the visit: The latch switch gets tested first, since it costs far less than a board.
Grit and food left on the top rack
A clogged filter recirculating dirty water, or spray arm jets narrowed by mineral scale so the upper rack gets a weak wash while the machine sounds normal. On the visit: The tech pulls the spray arms to check the jets and looks at the filter and sump for buildup.

Hard water dishwasher problems in Houston

Houston's 2025 water report shows Main System hardness averaging 135.5 mg/L and topping out at 229. Minerals at that level dry as white film on glassware, narrow the small jets in the spray arms and can coat the screen on the inlet valve until the fill slows. If your glasses come out cloudy and the cycle seems to take longer than it used to, mention both on the call.

Water temperature shows up the same way. Whirlpool's target is 120°F at the point the supply reaches the machine. In a house where the kitchen sits far from the water heater, the first fill can arrive lukewarm, so the machine stops to heat it and the wash may come out weaker. Samsung's 3E code is the reverse: the supply is too hot, and Samsung asks for under 176°F.

Glasses with white water spots on a dishwasher top rack

Dishwasher repair cost, part by part

National averages put most dishwasher repairs between $100 and $300, with an average near $200 and a high end around $650. Consumer Reports gives a median of about $142 from surveys of more than 125,000 members. Your tech works out the Houston price for your machine and shows it to you in writing before starting the repair.

RepairTypical rangeNotes
Diagnostic visit$70 to $130Includes the first hour of work
Water inlet valve$80 to $170Slow fill, no fill, or water trickling in with the machine off
Air gap installation$80 to $150
Door spring or latch$90 to $160
Filter replacement$90 to $175When cleaning no longer clears it
Float switch$90 to $190Overfilling, or no fill at all
Drain pump$100 to $400The pump part alone runs $20 to $100
Heating element$200 to $350Part $25 to $75
Control board$200 to $600
Motor with pump assembly$350 to $500Part $130 to $300

Figures are national averages with parts and labor included, except where a part price is shown. Washers, fridges, ovens and the rest are priced in the appliance repair cost guide.

Is a nine-year-old dishwasher worth fixing?

Nine years is about what the NAHB's study of home component lifespans gives a dishwasher, near the bottom of its kitchen list, and Consumer Reports says its dishwasher data typically leans toward replacement. The part on the quote and the age of the machine settle it.

Usually worth the repair

  • A machine still inside its first-year manufacturer warranty
  • An inlet valve, latch, float switch or filter, each under $200 in the table above
  • A drain pump on a dishwasher only a few years old
  • A panel-front or built-in model where a new one would mean cabinet or trim work

Usually time for a new one

  • A motor and pump assembly ($350 to $500) on a machine in its ninth year
  • A repair costing more than half the price of a comparable new dishwasher
  • Rust through the tub, or a leak from the tub itself rather than a hose or seal
  • A control board and a second major part found on the same visit

Bosch, Whirlpool and KitchenAid dishwasher repair

KitchenAid, Maytag, JennAir and Amana all belong to Whirlpool Corporation, so read us the name on the door and the model number together. Look up your street's ZIP on the service area list. Don't see your ZIP? Call anyway and we'll check your address.

Dishwasher repair questions

How much does it cost to fix a dishwasher that won't drain?

It depends on where the water is stuck. A packed filter or a crushed hose is a short job. A new drain pump runs $100 to $400 installed by national averages, with the pump itself $20 to $100. You'll see the written price before the tech replaces anything.

Why does my dishwasher smell bad even after a cycle?

Food trapped in the filter and sump is the usual cause, and it keeps rotting between runs. A drain hose without a high loop can also let sink water drift back into the tub. Smell plus standing water points to a drain problem, so the tech starts at the filter and the hose route.

How often does a dishwasher repair fix it the first time?

Most of the time. In Consumer Reports' 2021 member survey, 73 percent of dishwashers repaired by a professional were fixed on the first attempt and 18 percent on a later visit. Reading us the model number and any code helps the tech bring the right part on the first trip.

Can a dishwasher be fixed on the first visit?

Often, when the part is a common one like an inlet valve or a drain pump. A control board or a motor assembly is usually ordered against your model number, so the tech may come back once that part arrives.

My dishwasher is less than a year old. Is it still covered?

Probably. GE and Whirlpool both cover their dishwashers for one year from the purchase date, and other brands set their own terms. If yours is inside that first year, say so on the call and keep the receipt nearby.

Tub still full after the last cycle?

On the visit the tech traces the water from the filter to the pump and hose, then writes down the price for you to approve.

Call (713) 379-8612